P Forsmark site investigation. RAMAC and BIPS logging in borehole KFM01A. Jaana Aaltonen, Christer Gustafsson Malå Geoscience AB/RAYCON - PDF

P Forsmark site investigation RAMAC and BIPS logging in borehole KFM01A Jaana Aaltonen, Christer Gustafsson Malå Geoscience AB/RAYCON April 2003 Svensk Kärnbränslehantering AB Swedish Nuclear Fuel

Please download to get full document.

View again

of 28
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.

Food & Beverages

Publish on:

Views: 15 | Pages: 28

Extension: PDF | Download: 0

P Forsmark site investigation RAMAC and BIPS logging in borehole KFM01A Jaana Aaltonen, Christer Gustafsson Malå Geoscience AB/RAYCON April 2003 Svensk Kärnbränslehantering AB Swedish Nuclear Fuel and Waste Management Co Box 5864 SE Stockholm Sweden Tel Fax ISSN SKB P Forsmark site investigation RAMAC and BIPS logging in borehole KFM01A Jaana Aaltonen, Christer Gustafsson Malå Geoscience AB/RAYCON April 2003 Keywords: BIPS, RAMAC, radar, TV, geophysical logging This report concerns a study which was conducted in part for SKB. The conclusions and viewpoints presented in the report are those of the authors and do not necessarily coincide with those of the client. A pdf version of this document can be downloaded from Contents 1 Introduction 5 2 Objective and scope 7 3 Equipment RAMAC TV-Camera, BIPS 10 4 Execution Data acquisition Analyses and Interpretation 13 5 Results and data deliery RAMAC logging BIPS logging 18 6 References 19 Appendix 1 Radar logging of KFM01A Dipole antennas 250, 100 and 20 MHz 21 3 4 1 Introduction This document reports data gained during borehole logging, which is one of the activities performed within the site investigation at Forsmark. The logging operations presented here include borehole radar (RAMAC) and TV-logging (BIPS) and were carried out in the core drilled part of the m long telescopic borehole KFM01A (see Figure 1-1), from 100 m to approximately 990 m. The diameter of the core drilled part is c. 76 mm. Borehole section m, which is percussion drilled and today supplied with a casing of 200 mm inside diameter, was previously planned to be RAMAC- and BIPS-logged within the frame of another activity. However, due to an instability in the borehole, only section 0 50 m was possible to accomplish /1/. Hence, RAMAC- and BIPS-logging has been performed within the intervals 0 50 m and m in borehole KFM01A. The measurements were conducted by Malå Geoscience AB/RAYCON in December The work was carried out according to activity plan AP PF (SKB internal controlling document). The investigation techniques comprised: Borehole radar with both dipole and directional radar antennas. Borehole TV logging with the so called BIP-system (Borehole Image Processing System), which is a high resolution, side viewing, colour borehole TV system. Figure 1-1. Overview of drillsite No. 1 in the Forsmark area. 5 6 2 Objective and scope The objective of the radar- and BIPS-surveys was to achieve information on the borehole conditions (borehole wall and borehole fluid) as well as on the rock mass surrounding the borehole. Borehole radar was engaged to investigate the nature and structure of the rock mass enclosing the borehole, and borehole TV for geological surveying of the borehole wall including determination of fracture distribution and orientation. This report describes the equipment used as well as measurement procedures and data gained. For the BIPS-survey, the result is presented as images. Radar data are presented in radargrams, and the identified reflectors are listed in tables. 7 3 Equipment 3.1 RAMAC The RAMAC GPR system owned by SKB is fully digital, and emphasis has been laid on high survey speed and smooth field operation. The system operates dipole and directional antennas (see Figure 3-1). A system description is given in the method description Metodbeskrivning för borrhålsradar (SKB MD , Version 1.0). The borehole radar system consists of a transmitter and a receiver. During operation, an electromagnetic pulse within the frequency range of 20 to 250 MHz is emitted and penetrates the bedrock. The resolution and penetration of the radar waves depend on the antenna frequency used. A low antenna frequency results in a lower resolution but higher penetration rate compared to a higher frequency. If a feature, e.g. a water-filled fracture, with anomalous electrical properties compared to the surrounding is encountered, the pulse is reflected back to the receiver and recorded. Receiver (Rx) Transmitter (Tx) Glass fiber rod separating the two antennas Figure 3-1. Example of a borehole antenna. 9 3.2 TV-Camera, BIPS The BIPS 1500 system used is owned by SKB and described in the method description Metodbeskrivning för TV-loggning med BIPS (SKB MD , Version 1.0). The BIPS method for borehole logging produces a digital scan of the borehole wall. In principle, a standard CCD video camera is installed in the probe in front of a conical mirror (see Figure 3-2). An acrylic window covers the mirror part, and the borehole image is reflected through the window and displayed on the cone, from where it is recorded. During the measuring operation, pixel circles are scanned with a resolution of 360 pixels/circle. The system orientates the BIPS images according to two alternative methods, either using a compass (vertical boreholes) or with a gravity sensor (inclined boreholes). Figure 3-2. The BIP-system. Illustration of the conical mirror scanning. 10 4 Execution 4.1 Data acquisition RAMAC For the borehole radar measurements, both dipole and directional antennas were engaged. The dipole antennas are operated with central frequencies of 20, 100, and 250 MHz, respectively, whereas the directional antenna has a central frequency of 60 MHz. During logging, the dipole antennas (transmitter and receiver) were lowered continuously into the borehole and the data recorded on the field PC. The measurements with the directional antenna were made step-wise, with a short pause for each measurement. The antennas (both dipole and directional) are kept at a fixed separation by glass fibre rods according to Table 4-1. See also Figures 3-1 and 4-1. For detailed information, see SKB MD for method description and MD ( Instruktion för rengöring av borrhålsutrustning och viss markbaserad utrustning ) for cleaning of equipment. Information on the system settings for the different antennas used in the investigation of KFM01A is presented in Table 4-1 below. Figure 4-1. The principle of a radar borehole reflection survey (left) and a resulting radargram (right). 11 Table 4-1. Radar logging information from KFM01A. Site: Forsmark Logging company: RAYCON BH: KFM01A Equipment: SKB RAMAC Type: Directional / Dipole Manufacturer: MALÅ GeoScience Operators: CG / JA Antenna Directional 250 MHz 100 MHz 20 MHz (60 MHz) Logging date: Reference: T.O.C. T.O.C. T.O.C. T.O.C. Sampling frequency (MHz): Number of samples: Number of stacks: Signal position: Logging from (m): Logging to (m): Trace interval (m): Antenna separation (m): BIPS For detailed information on BIPS measurements, see SKB MD for a method description and MD for cleaning of equipment. During the measurement, a pixel circle with a resolution of 360 pixels/circle was stored at every 1 millimetre on a MO-disc in the surface unit. The maximum speed during data collection was 1.5 metre/minute. A gravity sensor measured the orientation of the image. Depth measurements The depth recording for the RAMAC and BIPS systems is taken care of by a measuring wheel mounted on the cable winch. Whenever reference marks in the borehole are visible on the image displayed by the ground unit during the BIPS logging, the logging cable is marked with a piece of red scotch tape. These marks are then used for controlling the depth registration during the RAMAC measurements. In Figure 4-2, the divergence between the individual measurements and the difference compared to the reference marks is plotted. The difference is increasing towards depth due to stretching of the measurement cable. The length recordings of the radar measurements were adjusted before the final data delivery. The difference between the dipole antennas and the directional antenna is due to the fact that different systems are used for calibration of the depth recordings. In the directional antenna system the depth recording is implemented in the automatic winch control, whereas for the dipole antennas the measurement software controls the depth. 12 Directional 20 MHz 100 MHz 250 MHz 40 Diffterence (cm) Depth (m) Figure 4-2. Illustration of the divergence in depth measurements for the different radar antennas used and the difference compared to the borehole reference marks. The depths of the dipole antennas are larger than the depth of the borehole reference marks, whereas the depth of the directional antenna is less. 4.2 Analyses and Interpretation Radar The result from radar measurements is generally presented in the form of a radargram where the position of the probes is displayed along one axis and the propagation along the other axis. The amplitude of the received signal is illustrated with a grey scale, where black colour corresponds to large positive signals and white colour to large negative signals. Grey colour represents no reflected signals. The data presented in this report are related to the measurement point, which is defined to be the centre between the transmitter and the receiver antenna. In the reflection mode, borehole radar measurements primarily offer a high-resolution image of the rock mass, visualizing the geometry of plane structures (contacts between rock units of different lithology, thin marker beds, fractures, fracture zones etc), which may or may not intersect the borehole, or indicating local features (cavities, lenses etc) close to the borehole. The distance to a reflecting object or plane is determined by measuring the difference in arrival time between the direct and the reflected pulse. The basic assumption is that the speed of propagation is consistent in the rock volume investigated. There are several ways to determine the radar wave propagation velocity. Each of them has its advantages and its disadvantages. In this project, the velocity determination was performed by keeping the transmitter fixed in a borehole at drillsite No. 1 (the percussion drilled borehole HFM03) while moving the receiver downwards in the borehole. The result is plotted in Figure 4-3. The calculation indicates a propagation velocity of 128 m/micro seconds. The velocity measurement was performed with the 100 MHz antenna /1/. 13 The visualization of data in Appendix 1 is made with REFLEX, a Windows based processing software for filtering and analysis of radar data. The processing steps are listed in Table 4-2. For interpretation of the intersection angle between the borehole axis and the planes visible on the radargrams, the RadinterSKB software has been applied. RadinterSKB is also used to interpret the orientation of structures identified in the directional antenna data. The interpreted intersection points and intersection angles of the detected structures are presented in the Table 5-1 and are also visible on the radargrams in Appendix 1. Figure 4-3. Results from velocity measurements in HFM03 /1/. Table 4-2. Processing steps for borehole radar data. Site: Forsmark Logging company: RAYCON BH: KFM01A Equipment: SKB RAMAC Type: Directional / Dipole Manufacturer: MALÅ GeoScience Interpret: JA Antenna Directional 250 MHz 100 MHz 20 MHz (60 MHz) Processing: DC removal DC removal DC removal DC removal Move start Move start Move start Move start time time time time FIR Dynamic Dynamic Dynamic correction correction correction Time gain Background Background Background removal removal removal Dewow Gain Bandpass Energy decay Dewow Energy decay BIPS The visualization of data is made with BDPP, a Windows based processing software for filtering, presentation and analyzing of BIPS data. No fracture mapping based on the BIPS images was performed. 14 5 Results and data deliery The results from the radar and BIPS measurements were delivered as raw data (*.bip files) on CD-ROMs to SKB together with printable BIPS pictures in *.pdf format before the field crew left the investigation site. The information of the measurements is registered in SICADA, and the CD-ROMs stored by SKB. RAMAC radar data were delivered as raw data (fileformat *.rd3 or *.rd5) with corresponding information files (file format *.rad), whereas the data processing steps and results are presented in this report. Relevant information, including the interpretation presented in this report, was inserted into the SKB database SICADA. The SICADA reference to the BIPS and RAMAC logging activity in KFM01A is Field note Forsmark RAMAC logging The results of the interpretation of the radar measurements are presented in Table 5-1. Radar data for the dipole antennas are also visualized in Appendix 1. It should be remembered that the images in Appendix 1 are only composite pictures of all events, 360 degrees around the borehole, and do not reflect the orientation of the structures. Results from measurements with the directional antenna are only presented in tabulated form, Table 5-2, with the identified planes and their orientation. Only the major, clearly visible structures are interpreted in RadinterSKB. A number of minor structures were encountered as well, as indicated in Appendix 1. It should be observed that none of the reflections is interpreted as parallel to the borehole. Hence, all of them intersect the borehole or it s imagined extension. The data quality, as seen in Appendix 1, is relatively satisfying. However, the measurements in part of the borehole suffer from deteriorated quality due to increased electrical conductive in the rock. A conductive environment entails attenuation of the radar waves, resulting in decreased penetration. As also seen in Appendix 1, the resolution and penetration of the radar waves depend on the antenna frequency. A high frequency will result in a high resolution but a lower penetration rate compared to a lower frequency. The identified structures intersecting the borehole are quite evenly distributed, see Table 5-1. Most structures are however encountered in borehole section m. Table 5-2 summarises the interpretation of radar data from KFM01A. Many structures can be identified in the data from more than one antenna frequency. When an object is detected by the directional antenna, the direction to the object (plane), as defined in Figure 5-1, is interpreted. 15 Table 5-1. Identified structures as a function of depth in KFM01A. Depth (m) No. of structures Depth (m) No. of structures Table 5-2. Model information from dipole antennas 20, 100 and 250 MHz and the directional, 60 MHz antenna. For the definition of direction to object, see Figure 5-1 RADINTER MODEL INFORMATION (20, 100 and 250 MHz Dipole Antennas and Directional Antenna) Site: Forsmark Borehole name: KFM01A Nominal velocity (m/µs): Object type Name Intersection depth Intersection angle Direction to object PLANE A PLANE B PLANE C PLANE D PLANE E PLANE F PLANE G PLANE H PLANE I PLANE J PLANE K PLANE L PLANE M PLANE N PLANE O PLANE P PLANE Q PLANE R PLANE S PLANE T PLANE U PLANE V PLANE Y PLANE Z PLANE PP (Å in App. 1) PLANE QQ (Ä in App. 1) PLANE RR (Ö in App. 1) PLANE AA Object type Name Intersection depth Intersection angle Direction to object PLANE BB PLANE CC PLANE DD PLANE EE PLANE FF PLANE GG PLANE HH PLANE II PLANE JJ PLANE KK PLANE LL PLANE MM PLANE NN PLANE OO Names in table according to Appendix 1. Side View: Antenna North Ground surface Intersection angle The plane Top View: The borehole 270 Direction to the plane = 0 degrees 90 Magnetic North of the Earth Figure 5-1. Definition of direction to object as presented in Table 5-2. In Appendix 1, the amplitude of the first arrival is plotted against depth for the 250 MHz dipole antenna. The amplitude variation along the borehole indicates changes of the electric conductivity of the material. A decrease in this amplitude may indicate fracture zones, clay or rock volumes with increased water content. An amplitude decrease is observed for the following sections in KFM01A , , , , , , , , and These sections coincide, at least partly, with sections where the highest number of structures has been identified, with a concentration to the upper part ( m) of the borehole. 17 5.2 BIPS logging To get the best possible depth accuracy, the BIPS images were adjusted to the reference marks along the borehole. However, below 650 m, the reference marks are missing, due to dis-functioning of the marker tool. In order to control the quality of the system, calibration measurements were performed in a test pipe before and after logging of the borehole. The resulting images displayed no difference regarding colours and focus of the images. Results from the test loggings were included in the delivery of raw data. The BIPS images from borehole KFM01A are impaired by some quality problems, which, however, are system independent. Instead, the problems are related to a drilling induced discolouring of parts of the borehole wall, see example in Figure 5-2. The water quality, which is another crucial factor for achieving a satisfactory quality of the BIPS images, turned out to be fairly good along the borehole during logging. Figure 5-2. Examples of BIPS images suffering from deteriorated quality caused by discolouring of the borehole wall. 18 6 References /1/ Gustafsson C, Nilsson P, Geophysical Radar and BIPS logging in borehole HFM01, HFM02, HFM03 and the percussion drilled part of KFM01A. SKB P Svensk Kärnbränslehantering AB. 19 Appendix 1 Radar logging of KFM01A Dipole antennas 250, 100 and 20 MHz 21 FORSMARK KFM01A 250 MHz 100 MHz 20 MHz 22 FORSMARK KFM01A 250 MHz 100 MHz 20 MHz 23 FORSMARK KFM01A 250 MHz 100 MHz 20 MHz 24 250 MHz FORSMARK KFM01A 100 MHz 20 MHz 25 FORSMARK KFM01A 250 MHz 100 MHz 20 MHz 26 250 MHz FORSMARK KFM01A 100 MHz 20 MHz 27 250 MHz FORSMARK KFM01A 100 MHz 20 MHz 28 FORSMARK KFM01A 250 MHz 100 MHz 20 MHz 29 FORSMARK KFM01A 250 MHz 100 MHz 20 MHz 30
Related Search
Similar documents
View more...
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks