Jøtul F 3 USA. Installation and Operating Instructions for the USA and Canada 2 Exploded view 20. Kindly save these instructions for future reference. - PDF

Description
Jøtul F 3 USA Jøtul F 3 USA Installation and Operating Instructions for the USA and Canada 2 Exploded view 20 Kindly save these instructions for future reference. Table of contents: Standards and Safety

Please download to get full document.

View again

of 24
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information
Category:

Education

Publish on:

Views: 26 | Pages: 24

Extension: PDF | Download: 0

Share
Transcript
Jøtul F 3 USA Jøtul F 3 USA Installation and Operating Instructions for the USA and Canada 2 Exploded view 20 Kindly save these instructions for future reference. Table of contents: Standards and Safety Notices Installations Chimney Requirements... 6 Masonry Chimney... 6 Prefabricated Chimney... 7 Chimney height... 7 Wall pass-throughs Connecting to the Chimney... 8 Masonry chimneys... 8 Hearthmount/Fireplaces... 8 Prefabricated Chimney /8 -707 mm 22 9/16 mm 4.0 Clearances Floor requirements Wall shields Stove Clearances /4 - 184 mm Alcove Installations Operation Controls Breaking in your new Stove Starting/Maintaining Formation of Creosote Maintenance Ash Removal Glass Care General Maintenance...17 Gaskets Accessories...18 Firescreen Floor Bracket Kit Stove -Top Thermometer /8 mm 22 9/16 mm Appendix A (alternate floor protecion)...19 Parts Diagram...20 Part list - 484mm Save these instructions and make them available to anyone using or servicing the stove. 22 3/4 mm 14 7/16 mm 71/4 -184mm 2 Installation and Operation Instructions for USA/Canada Installation et fonctionnement pour Canada Safety notice: If this solid fuel room heater is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Save these instructions for future reference. Avis de sécurité: Une installation non appropriée de ce poêle de chauffage risque de provoquer un incendie. Assurez votre sécurité en respectant les directives d installation suivantes. Consultez les autorités locales du bâtiment ou de la prévention des incendies au sujet des restrictions et exigences relatives aux inspections d installations dans votre région. Tested and listed by ITS, Intertek Testing Services, Middleton, Wisconsin. Tested to U.S. Standards: ANSI/UL 737 andansi/ul 1482, Canadian Standards: CAN/ULC-S627-M93 Standards The Jøtul F 3 woodstove has been tested and listed to: U.S. Standards: ANSI/UL 737 and ANSI/UL 1482 Canada: CAN/ULC-S627-M93 Tests performed by: ITS, Intertek Testing Services, Middleton, WI Manufactured by: Jøtul AS., P.O. Box 1411, Fredrikstad, Norway Distributed by: Jøtul North America Inc, 55 Hutcherson Drive, Gorham, Maine 04038, USA This heater meets the U.S. Environment Protection Agency s Emissions limits for wood heaters manufactured and sold after July 1, Under specific test conditions, this heater has shown heat output at rates ranging from 11,500 to 43,500 BTU s per hour. Check Building Codes When installing, operating and maintaining your Jøtul F 3 woodstove, follow the guidelines presented in these instructions, and make them available to anyone using or servicing the stove. Your city, town, county or province may require a building permit to install a solid fuel burning appliance. In the U.S., the National Fire Protection Association s Code, NFPA 211, Standards for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances, or similar regulations, may apply to the installation of a solid fuel burning appliance in your area. In Canada, the guideline is established by the CSA Standard, CAN/CSA-B365-M93, Installation Code for Solid- Fuel-Burning Appliances and Equipment. Always consult your local building inspector or authority having jurisdiction to determine what regulations apply in your area. The Jøtul F 3 woodstove is only listed to burn wood. Do not burn any other fuels. Read this entire manual before you install and use your new room heater. Save these instructions and make them available to anyone using or servicing the stove. 3 Notices Be sure to read this entire manual before you install or use your new Jøtul F 3. If this room heater is not properly installed, a house fire may result. To reduce the risk of fire, follow the installation instructions. Failure to follow these instructions may result in property damage, bodily injury, or even death. Jøtul recommends that you have your new Jøtul F 3 installed by a professional installer of solid fuel burning appliances. Extremely hot while in operation! Keep children, clothing and furniture away. Contact may cause skin burns. Avoid creating a low pressure condition in the room where the stove is operating. Be aware that operation of an exhaust fan or clothes dryer can create a low pressure area and consequently promote flow reversal through the stove and chimney system. The chimney and building, however, always work together as a system - provision of outside air, directly or indirectly to an atmospherically vented appliance will not guarantee proper chimney performance. Consult your local Jøtul authorized dealer regarding specific installation/performance issues. Reminder: Your local officials have final authority in determining if a proposed installation is acceptable. Any requirement, that is requested by the local authority having jurisdiction, that is not specifically addressed in this manual, defaults to NFPA 211, and local codes. In the U.S. or in Canada, CAN/CSA-B365-M and local codes. Installing the venting The Jøtul F 3 can be vented from the top, the rear or from either the right or left side. Follow the instructions below for the desired venting location. Top exit venting When top exit venting is desired, use a 3mm allen wrench to remove the two set screws that secure the top casting to the sides of the stove and lift off the top casting. Lay the top casting on a flat surface upside down and remove the 10mm bolt from the traverse bar and remove the smoke outlet cover. Reinstall the top casting, be sure to secure with the two set screws that were removed. See figure 1. Fig. 1 Upside down Top casting Stove pipe stop Do not use chemicals or fluids to start the fire. Some fuels will, during combustion, separate carbon monoxide and generate it in the burn chamber. Carbon monoxide is toxic, so please follow the guidelines in this manual for proper operation of your Jøtul F 3. If you for some reason experience smoke roll-out from the stove, it may activate smoke detectors if installed in the house. Do not connect this stove to any air distribution duct or system. Traverse bar securing smoke outlet cover to top casting Stove pipe top 1.0 Installation If this solid fuel room heater is not properly installed a house fire may result. For your safety, follow the installation directions. Contact the local building or fire officials about restrictions and installation inspection requirements in your area. Rear exit venting When rear exit venting is desired it will be necessary to knock-out the vent hole from the rear casting. Remove the top casting of the stove by removing the two 3mm set screws that secures the top to the sides. The set screws are located on the outside of the stove on the top of each side panel. Using a 10mm wrench remove the double rear heatshields from the back of the stove. Remove the front door to avoid damage to the glass. Reminder: Loss of the door washer will result in improper door alignment when reinstalling the door. 4 Using a claw hammer or a small sledge hammer strike the center of the 6 knock-out disc from the outside of the stove. The knock-out disc will break into four wedges and may need to be tapped out. Touch up any remaining sharp edges with a file or hand grinder. Note: The ivory Jøtul F 3 s are rear vented from the factory. It is not necessary to knock-out the rear casting of the stove. However, if top exit is desired it is necessary to install a smoke outlet cover on the rear outlet of the stove. Reinstall the top casting and front door, remembering the washer. The two rear heatshields must be reinstalled on the stove. Remove the metal cover plates from the heatshields and reinstall. Reminder: There is a small nut used as a spacer between the two heatshields. See fig 2. Fig. 2 Spacers stove s internal collar, using the nuts and bolts provided with the stove. See figure 3. Fig. 3 Direction into the stove The adaptor should be inserted into the stove until the bead on the adapter is flush with the top, back or side casting. Now the adaptor is ready to accept single or double walled stove pipe. See figure 4. Each joint of chimney connector or stove pipe must be secured with at least three sheet metal screws to ensure that the sections do not separate. Fig. 4 Adaptor bead should be flush with stove Heatshield with listing label should be installed on the outside Side exit venting If venting through the side is desired it will be necessary to remove the top casting. Using a 3mm allen wrench remove the two set screws that secure to the top to the side panels. Remove the front door to avoid damage to the glass. Reminder: Loss of the door washer will result in improper door alignment when reinstalling the door. Using a claw hammer or a small sledge hammer strike the center of the 6 knock-out disc from the inside of the stove. The knock-out disc will break into four wedges and may need to be tapped out. Touch up any remaining sharp edges with a file or hand grinder. Reinstall the front door, remembering the washer and the top casting. Installing the stove pipe adapter After the appropriate flue outlet in the stove has been established the stove pipe adapter (included with every stove) must be installed so that standard stove pipe can be installed onto the stove. Insert the end of the adapter with the four holes into the stove. These holes allow the adaptor to be attached to the Stove pipe - chimney connector The chimney connector is a single walled pipe used to connect the stove to the chimney. For use with the Jøtul F3 the chimney connector must be 6 in diameter, with a minimum thickness of 24 gauge black steel. Aluminum and galvanized steel pipe is not acceptable for use with the Jøtul F3. These materials cannot withstand the extreme temperatures of a wood fire and can give off toxic fumes when heated. Each chimney connector or stove pipe section must be installed to the stove flue collar and to each other with the male (crimped) end toward the stove. See figure 5. Fig. 5 Crimped end installed toward the stove 5 This prevents any amount of condensed or liquid creosote from running down the outside of the pipe or the stove top. All joints, including the flue collar connection must be secured with three sheet metal screws to ensure that the sections do not separate. For the best performance the chimney connector should be as short and direct as possible, with no more than two 90 elbows. The maximum horizontal run is 36 and a recommended total length of stove pipe should not exceed 10 feet. Always slope horizontal runs upward 1/4 per foot toward the chimney. No part of the chimney connector may pass through an attic or roof space, closet or other concealed space, or through a floor or ceiling. All sections of the chimney connectors must be accessible for cleaning. Where passage through a wall or partition of combustible construction is desired, the installation must conform with NFPA 211 or CAN/CSA-B365, and is also addressed in this manual. Do not connect this unit to a chimney flue servicing another appliance. Do not use the connector pipe as a chimney. 2.0 Chimney requirements There are two types of chimneys suitable for the Jøtul F3: 1. A code- approved masonry chimney with a flue liner. 2. A prefabricated chimney complying with the requirements for type HT (2100 F) chimneys per UL 103 or ULC S629. The chimney size should not be less than the crosssectional area of the flue collar, and not more than three times greater than the cross-sectional area of the flue collar. When selecting a chimney type and the location for the ce of the chimney, as well as the proximity of surrounding trees or buildings. As a result, a short masonry chimney on the exterior of a house will give the poorest performance. This is because it can be very difficult to warm the chimney thereby creating inadequate draft. In extremely cold northern areas it may be necessary to reline the chimney or extend its height to help establish draft. Oppositely, a tall masonry chimney inside the house is easier to keep warm and will perform the best. The following guidelines give the necessary chimney requirements based on the national code (ANSI-NFPA 211 for the us. And CSA CAN-B365 for Canada). However, many local codes differ from the national code to take into account climate, altitude, or other factors. It is important that you check with your local building officials to find out what codes apply in your area before installing your new Jøtul F3. Masonry chimneys When installing the Jøtul F3 into a masonry chimney you must conform to all of the following guidelines: The masonry chimney must have a fireclay liner or equivalent, with a minimum thickness of 5/8 and must be installed with refractory mortar. There must be at least 1/2 air space between the flue liner and chimney wall. The fireclay flue liner must have a nominal size of 8 x 8, and should not be larger than 8 x 12. If a round fireclay liner is to be used it must have a minimum inside diameter of 6 and not larger than 8 in diameter. If a chimney with larger dimensions is to be used, it should be relined with an appropriate liner that is code approved. The masonry wall of the chimney, if brick or modular block, must be a minimum of 4 nominal thickness. A mountain or rubble stone wall must be at least 12 thick. A newly-built chimney must conform to local codes and in their absence must recognize national regulations. When using an existing chimney, it must be inspected by a professional licensed chimney sweep, fire official, or code officer, to ensure that the chimney is in proper working order. 6 No other appliance can be vented into the same flue. An airtight clean-out door should be located at the base of the chimney. Prefabricated chimneys If a prefabricated metal chimney is to be used it must be a chimney type that is tested and listed for use with solid fuel burning appliances. High temperature (ht) chimney standard UL103 for the U.S. And high temperature standard ULC S-629 for Canada. The manufacturer s installation instructions must be followed precisely. Always maintain the proper clearance to combustibles as established by the pipe manufacturer. This clearance is usually a minimum of 2, although it may vary by manufacturer or for certain chimney components. Chimney height Whether a masonry chimney or prefabricated metal chimney is used it must be the required height above the roof line. The requirement is: The chimney must be at least 3 feet higher than the highest point where it passes through the roof and at least 2 feet higher than the highest part of the roof or structure that is within 10 feet of the chimney, measured horizontally. See figure 6. Fig. 6 At least 3 feet At least 3 feet Wall pass-throughs USA/Canada When your installation unavoidably requires the chimney connector to pass through a combustible wall to reach the chimney, always consult your local building officials, and be sure any materials to be used have been tested and listed for wall pass-throughs. In the U.S. The national fire protection association s publication, NFPA 211, standard for chimneys, fireplaces, vents and solid fuel burning appliances permits four methods for passing through a combustible wall. Before proceeding with any method be sure to consult with your local building officials to discuss any local code requirements. Common method When passing through a combustible wall to a masonry chimney this method requires the removal of all combustible materials from at least 12 around the chimney connectors proposed location. With a 6 round liner the minimum area required would be 31 x 31 square. The space is then filled with at least 12 of brick around a fireclay liner. Remember, the liner must be ASTM C35 or equivalent, with a minimum wall thickness of 5/8. It is important to remember to locate the pass-through at least 18 from the ceiling for proper clearance to combustibles. It will be necessary to cut wall studs, install headers, and construct a sill frame to maintain the proper dimensions and to support the weight of the brick. The bricks must be solid brick with a minimum of 3 1/2 thick (4 nominal). Refractory mortar must be used at the junction of the chimney and the pass-through liner. The pass-through liner must not penetrate the chimney liner beyond the inner surface of the chimney liner. Use extreme care when constructing the hole in the chimney liner, the tiles can shatter easily. See figure 7. Fig. 7 Wood Stud 2 Clearance to Chimney Flue Liner 10 feet Chimneys shorter than 14 feet may not provide adequate draft. This could result is smoke spilling into the room from the stove when loading the stove, or when the door is open. In addition, inadequate draft can cause back puffing, which is a build up of gases inside the firebox. Other times, chimney height can create excessive draft which can cause high stove temperatures and short burn times. Excessive drafts can be corrected by installing a butterfly damper. If you suspect you have a draft problem, consult your dealer. Header cm Pass through construction: 12 Brick from thimble to combustibles Thimble: 5/8 Fireclay Liner or equivalent Sill / Support 7 In Canada In Canada the standard has been established by the canadian standard association. The installation must conform to CAN/CSA-B365, installation code for solid fuel burning appliances and equipment. Before proceeding be sure to consult your local building inspector. Common method This method requires the removal of all combustible materials from at least 18 (457mm) around the chimney connector s proposed location. With a 6 round liner the minimum area required would be 43 x 43 square. It is important to remember to locate the pass-through at least 25 from the ceiling to maintain the proper clearance to combustibles. 3.0 Connecting to the chimney Masonry chimney When installing a Jøtul F 3 into a masonry chimney through a thimble (the opening through the chimney wall to the flue), the thimble must be lined with ceramic tile or metal and be securely cemented in place. The chimney connector/stove pipe must slide completely inside the thimble to the inner surface or the flue liner. It may be necessary to make use of a thimble sleeve (a pipe with a slightly smaller diameter than standard stove pipe). This special pipe can be easily installed into a thimble. See Figure 8. The space that is cleared of combustible materials must then remain empty. Sheet metal panels can then be used to cover the area. However, when using a panel on both sides of the wall each cover must be installed on noncombustible spacers at least 1 from the wall. If one panel of sheet metal is to be used it may be installed flush to the wall. See section and of CAN/CSA - B365-m91. Consult your local building inspector, authorized Jøtul Dealer, NFPA 211 in the U.S. or CAN/CSA-B635 in Canada for other approved wall pass-through methods. Fig. 8 Connector pipe must be flush with the inside of the flue tile Chimney Connector Pipe Thimble Flue Tile Make sure the connector pipe or thimble sleeve does not protrude into the flue liner, thereby restricting the area the smoke has to flow through. This bottle-neck will have a negative affect on the chimney system. The chimney connector should be sealed at the thimble with refractory cement and the stove pipe leading to the stove should have a minimum of three screws. Do not connect this stove to a chimney flue servicing another appliance of any kind. Hearth-mount into a masonry fireplace The Jøtul F 3 may be installed into a masonry fireplace provided the opening is a minimum of 28 1/2 high. The short leg package reduces the stove s height by 2 1/4. When installing the Jøtul F 3 into a masonry fireplace, code requires that the fireplace damper plate be removed or securely fixed in the open position. A connector pipe must th
Related Search
Similar documents
View more...
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks