Hot-Wire Anemometry. Csaba Horváth - PDF

Hot-Wire Anemometry Csaba Horváth Anemometry Anemometry: Measurement of fluid velocity What kind of anemometers exist? History: Introduced in the first half of the 20th century Commercially available in

Please download to get full document.

View again

of 25
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.


Publish on:

Views: 103 | Pages: 25

Extension: PDF | Download: 0

Hot-Wire Anemometry Csaba Horváth Anemometry Anemometry: Measurement of fluid velocity What kind of anemometers exist? History: Introduced in the first half of the 20th century Commercially available in their present form since the nineteen-fifties Used for measuring the mean and fluctuating variables in fluid flows (velocity, temperature, etc.), with an emphasis on mean velocity and turbulence characteristics The measurement technique is based on the heat transfer from a heated wire to the relatively cold surrounding fluid. This heat transfer is a function of the fluid velocity Relationship between the fluid velocity and the electrical output of the system can be established. Anemometer signal output The thermal anemometer provides an analogue output which represents the velocity in a point. Velocity information is thus available anytime. Note that LDA signals occur at random, while PIV signals are timed with the frame grapping of illuminated particles. Measurement Chain Probe, wire, bridge (Wheatstone bridge for CTA), signal conditioner, D/A convertor, computer, computer program Probe types I Miniature Wire Probes Platinum-plated tungsten, 5 m diameter, 1.2 mm length Gold-Plated Probes 3 mm total wire length, 1.25 mm active sensor copper ends, gold-plated Advantages: - accurately defined sensing length - reduced heat dissipation by the prongs - more uniform temperature distribution along wire - less probe interference to the flow field Probe types II Film Probes Thin metal film (nickel) deposited on quartz body. Thin quartz layer protects metal film against corrosion, wear, physical damage, electrical action Fiber-Film Probes Hybrid - film deposited on a thin wire-like quartz rod (fiber) split fiber-film probes. Probe types III X-probes for 2D flows 2 sensors perpendicular to each other. Measures within ±45 o. Split-fiber probes for 2D flows 2 film sensors opposite each other on a quartz cylinder. Measures within ±90 o. Tri-axial probes for 3D flows 3 sensors in an orthogonal system. Measures within 70 o cone. Probe types: advanced I 1d, 2d, 3d Hot-wire, hot-film The supports are called prongs, needles or stems Wire is the measurement material Stubs or wire ends are the parts of the wire near the prongs Hot-wire probe (normal and miniature probe) Wire length: 1-3 mm ( other source says mm) Wire diameter is typically 5 μm (between 1-10 μm, other source says μm) Hot-film probe Layer of about 0.1 μm thick deposited of substrate Substrate Fine cylinders of quartz, about μm in diameter Quartz wedges Thin acetate or kapton foils. Very thin quartz coating deposited on the sensor provides both protection against a hostile environment and isolation when operating in a conductive medium Probe types: advanced 2 The small dimensions give a small measurement volume The material for sensors should have the following properties High value of the temperature coefficient of resistance, Increased sensitivity to velocity variations Electrical resistance such that it can be easily heated with an electrical current at practical voltage and current levels Possibility of being available as wire of very small diameter High enough tensile strength To withstand the aerodynamic stresses at high flow velocities Common materials: Tungsten, platinum, platinum-iridium alloys Tungsten: Mechanically strong, High temperature coefficient of resistance (0.004/ C) Poor resistance to oxidation at high temperatures in many gasses. Most popular When coated with a thin platinum layer, it becomes more resistive to oxidation, changes temperature coefficient to / C and soldering is eased. Platinum: Good oxidation resistance Good temperature coefficient of resistance (0.003/ C), mechanically weak (particularly at high temperatures) Platinum-iridium alloy: compromise between the other two Good oxidation resistance Higher tensile strength than platinum Low temperature coefficient of resistance ( / C) Platinum-rhodium alloy: Higher temperature coefficient than platinum-iridium Not as strong mechanically as platinum-iridium Probe types. advanced 3 Coated wire ends/stubs Gold or copper material Results in better mechanical and aerodynamic properties Reduced heat transfer to the prongs Smaller, better defined measurement length Miniaturized hot-wire probes are recommended for low subsonic flows. This helps to make the probes as non-intrusive as possible. Film vs. Wire Hot-wire sensors provide superior performance in many applications Hot-film typically has a larger diameter, and therefore a lower spatial resolution In applications requiring maximum frequency response, minimum noise level and very close proximity to a surface, the platinum-coated tungsten hot wire sensor is superior Hot-film is more robust than hot-wire Hot-film is less sensitive to dirt and is easier to clean Hot-film has a more complex material and also a lower frequency response Probe types: advanced 4 Bridge: circuitry Provides the wire a controlled amount of electric current Operation Principle Consider a thin wire mounted to supports and exposed to a velocity U. When a current is passed through wire, heat is generated (I 2 R w ). In equilibrium, this must be balanced by heat loss (primarily convective) to the surroundings. If velocity changes, convective heat transfer coefficient will change, wire temperature will change and eventually reach a new equilibrium. Velocity U Current I Sensor (thin wire) Sensor dimensions: length ~1 mm diameter ~5 micrometer Wire supports (St.St. needles) Governing equation Governing Equation: de dt W H E = thermal energy stored in wire E = CwTw Cw = heat capacity of wire W = power generated by Joule heating W = I 2 Rw recall Rw = Rw(Tw) H = heat transferred to surroundings Simplified static analysis I For equilibrium conditions the heat storage is zero: and the Joule heating W equals the convective heat transfer H Assumptions de dt O W H - Radiation losses small - Conduction to wire supports small - Tw uniform over length of sensor - Velocity impinges normally on wire, and is uniform over its entire length, and also small compared to sonic speed. - Fluid temperature and density are constant Simplified static analysis II Static heat transfer: W = H I 2 Rw = ha(tw -Ta) I 2 Rw = Nukf/dA(Tw -Ta) h A d kf Nu = film coefficient of heat transfer = heat transfer area = wire diameter = heat conductivity of fluid = dimensionless heat transfer coefficient Forced convection regime, i.e. Re Gr 1/3 (0.02 in air) and Re 140 Nu = A 1 + B 1 Re n = A 2 + B 2 U n I 2 Rw 2 = E 2 = (Tw -Ta)(A + B U n ) The voltage drop is used as a measure of velocity A, B, n: BY CALIBRATION King s law data acquisition, processing Advanced Operation Principle I Supply= I 2 R w = πdlh(t w -T a )= Dissipation I= heating current flowing in the wire [A] R w = resistance in the wire at the operating temperature *Ω+ D= diameter of the wire [m] l= length of wire [m] h= heat transfer coefficient [W/(m 2 K)] T w = wire temperature * c+ T a = fluid (air) temperature * c+ The Nusselt number is a dimensionless number relating the convective and the conductive heat transfer across (normal to) the boundary: Nu= Convective heat transfer coefficient/conductive heat transfer coefficient Nu= hd/k I 2 R w = πlk(t w -T a )Nu I 2 R w = A+BU n (T w -T a ) A= represents the natural convection term BU n = represents the forced convection term U= flow velocity [m/s] Advanced Operation Principle II If one wants to increase the resolution of the measurements, the influence of the natural convection term should be minimized. Good working conditions are reached when: (l/d)(gr 1/2 ) 1 (or alternatively, Re Gr 1/3 ) Gr being the Grashof number Gr= (g(t w T a )D 3 )/(T m ν 2 ) The resistance of a wire is a function of its temperature. For a metallic conductor: R w = R a [1+b 1 (T w -T a )+b 2 (T w -T a ) This can be linearized for a temperature range of up to 200 c R w = R a [1+b 1 (T w -T a )] This results in the following expression: b 1 (I 2 R w R a )/(R w R a )=A+BU n Thus the actual value of the heat transfer could be obtained either as the value of R w if I is kept constant. Constant Current Anemometry method the value of I if R w is kept constant. Constant Temperature Anemometry method Since the frequency response of the the sensors are mostly flat (linear) in a large range (order of 100 Hz- order of Hz) This allows the instantaneous response of the hot-wire to be written, even for unsteady flows, in an algebraic form as : E 2 =A+B(U) n. King s law E 2 =A+BU n +CU: Gaulier s modified law U=k 1 +k 2 E+k 3 E 2 +k 4 E 3 + +k i+1 E i : polynomial fit Advanced Operation Principle III Control circuits The main difference between the operating modes is linked to the handling of thermal inertia of the sensor. In usual applications, the frequencies of the flow fluctuations to be measured are much higher than the natural frequency of the sensor Therefore electronic compensation is needed In a CCA and CVA, this is achieved by a first-order high-pass filter integrated in the amplifying unit. In a typical CCA application, the filter s response is tuned to compensate exactly the thermal lag of the sensor. The overall bandwidth is then only limited by the amplifier s characterisitics, mainly its gain-bandwidth product. With a CVA, the thermal ld is partially compensated during measurements and is fully compensated when post-processing the data. This permits high productivity for largebandwidth applications because no adjustment is required when the experiment is running. In a CTA, the temperature of the sensor is maintained constant by a feedback loop, so that its thermal inertia is, in principle, automatically compensated. In this case, the maximum bandwidth is limited by the amplifier s properties and some characteristics of the practical setup. Full compensation can be made after carefully tuning the circuit. Advanced Operation Principle IV Constant current anemometry (CCA): In its basic form, the control circuit may be reduced to a source of constant current feeding a calibration and measurement bridge. The two resistors are chosen to be equal and the value of R is chosen to be equal to the hot resistance of the wire ( usually 1.8 times the cold wire resistance) and the supply current is increased until, for zero wind velocity, a balance is obtained at the bridge output. Any change in wind velocity will change the heat transfer, and thus the wire temperature and resistance and cause an unbalanced voltage to appear at the bridge output. This can be calibrated against flow velocity to obtain the wire calibration curve. Has a slow frequency response due to the circuits own thermal inertia. R w =const., I =I(U) Constant temperature anemometry (CTA): The output from the bridge is amplified and used to control the supply voltage such as to maintain the wire temperature constant. The amplifier output E, required to maintain the wire at a constant temperature is a function of the flow velocity. The temperature is again fixed by the choice of the resistance R of the bridge (usually 1.8 times the cold wire resistance). All coefficients can be considered constants. Because the changes in temperature are now much smaller, the thermal inertia of the wire can be expected to play a minor role in determining the frequency response. Because the temperature of the wire remains almost constant, all nonlinearities introduced by the thermal lag effect are substantially smaller and in most cases negligible. The new frequencies to be considered are so high that the reactive phenomena taking place in the wire connection cables and in the amplifier must be taken into account and these increase the order of the response equation. Accounting for a change in T a, the temperature of the measured fluid, is important. I =const., R w = R w (U) Constant voltage anemometry (CVA) (new) Directional response Probe coordinate system y U Uz Uy x Ux z Velocity vector U is decomposed into normal Ux, tangential Uy and binormal Uz components. Calibration Velocity calibration: Velocity calibration range: 0.1*U min - 1.5*U max Need to calibrate the system for the flow angles in case of a multi-component probe Done within the range of the acceptable measuring angle Dynamic bridge balancing: Square wave test A square wave is given at the wire terminal and the response of the system is monitored on an oscilloscope Balance the system Therefore optimizing the combined sensor/anemometer circuit to receive the best possible bandwidth (best frequency response and therefore highest possible frequency measurement) or limiting frequency Since frequency response is a function of the fluid velocity Done at the mean flow velocity at which the probe is likely to operate In case of impulsive flows, done at the mean value of velocity Advantages and disadvantages I Advantages of hot-wire anemometers: Cost is relatively cheap Frequency response is high Size: small measurement volume Good spatial and temporal resolution Turbulent flows can easily be measured with it Multi-component measurement Simultaneous temperature measurement: available with multi-sensor probe Two-phase flow measurement is possible Accuracy is as good as a Laser Doppler anemometer Signal-to-noise ratio is low Probe and analysis selection: It is easy to find a good measurement system for most measurements Signal analysis: Analogue output provides an opportunity for conditionally-sampled time-domain and frequency-domain analysis Spatial separation: Multi-component probes allow for the measurement of multi-component flows Special probes can easily be made Measurements can be made in gases, transparent, opaque, and even electrically conducting liquids. Can measure instantaneous wall shear stresses with wall sensors mounted flush to the surface Advantages and disadvantages II Hot-wire anemometer problems High turbulence intensity Restricted to low and moderate turbulence intensity flows Flow disturbance from outside the measurement plane alters results Liquid flows Can contaminate the probe more easily Temperature changes in the fluid effect the results more due to the smaller overheat ratio which is used in liquids Probe breakage Contamination Intrusive method Heat transfer between the probe and surfaces or the support prongs Noise in the signal Radio frequency signal noise Circuitry noise Heat transfer problems Supports are not as hot as the sensor, due to their larger mass. They act as heat sinks. Therefore the edge of the wire is cooled, reducing the active wire length. This can be accounted for by calibration, and is less of an issue in CTA then in CCA. Thermal wake from one wire could effect the measurements on another probe for a multi-component hot-wire probe. The wires are sensitive to both temperature and velocity, and therefore if both change simultaneously, then the results are contaminated. (Ex. Geophysical flows, high subsonic and transonic flows.) Aerodynamic problems Probes are not sensitive to flow direction (reverse flow) Probe supports interfere with the flow onto the other sensors (multi-component probes, multi-probe arrangements (such as for space correlation measurements)) Etc Traverse system Software Calibration system Applications Turbulence properties
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!